The stand must simulate the operating mode and measure the output characteristics of the removed electrical equipment in order to check its functionality, as well as determine the technical condition and troubleshoot. Must ensure verification of: relay regulators; relay-breakers; electric drives of vehicle components; generators under load and at idle; starters in full braking and […]

Purpose. The laboratory bench simulator is intended for carrying out a set of practical work on studying the technology for diagnosing gasoline injection nozzles, as well as developing initial skills in diagnosing, maintaining and repairing a car in the courses “Design of automotive equipment”, “Operation of automotive equipment”, “Design and calculation of automobile technology.» Description. […]

The complex should include two devices. The first device removes carbon deposits and other contaminants using sandblasting and blowing with compressed air. For cleaning, molding sand with a grain size of 0.14-0.18 mm is used. Connects to the compressed air network. The second device for checking spark plugs. Allows you to test the spark plug […]

Description. The simulator stand is designed for diagnosing and adjusting injection pumps of domestic and foreign production up to 12 sections inclusive. At the stand it is possible to diagnose fuel injection pumps of various types: in-line BoschK, M, MW,A, B, BV,P; MOTORPAL; distribution injection pumps: Bosch, Lucas, Zexel, Denso. Domestic fuel injection pumps: YAZTA, […]

The stand-simulator “Diagnostics of diesel electromagnetic injectors” is intended for training students of automobile repair specialties of secondary and primary vocational education institutions in the basics of working with diagnostic devices that allow them to control the injectors of the Common Rail fuel supply system and check their performance (pattern and intensity of spray, volumetric […]

A two-post lift with lower synchronization and a lifting capacity of at least 4 tons, designed for lifting all-wheel drive passenger cars and light trucks with subsequent fixation at working height for the purpose of repair or maintenance. Functional features: bottom synchronization; the control panel must be equipped with a printed circuit board that itself […]

Purpose: The training stand is a set of various automotive locksmith equipment intended for the implementation of training for a standard group of trainees from 5 to 10 people when teaching the basics of the technology of instrumental diagnostics, repair and maintenance of internal combustion engines and transmissions, as well as the technology of their […]

The training stand is designed to teach students of automobile repair specialties from secondary and primary vocational education institutions the basics of working with installations for determining wheel alignment and camber of passenger cars, methods of setup, maintenance and operation in the conditions of car repair shops and bases of automobile repair enterprises. Description. The […]

The stand-simulator “Technical Control Line” is intended for carrying out a set of practical work on studying modern methods of diagnostics and technical control of passenger cars and light trucks of imported and Russian production, as well as developing initial skills in vehicle maintenance and repair in the courses “Automotive Equipment Design”, “Operation of Automotive […]

Purpose. The training simulator is designed to carry out a set of practical work on studying the technology of cleaning fuel systems of gasoline and diesel engines without disassembling and removing injectors, as well as developing initial skills in diagnosing, maintaining and repairing a car in the courses “Design of Automotive Equipment”, “Operation of Automotive […]

Purpose. The stand-simulator “Automotive CAN bus scanners” is intended for carrying out a set of practical work on studying modern methods of digital diagnostics of passenger cars and light trucks of imported and Russian production, as well as developing initial skills in vehicle maintenance and repair in the courses “Automotive Equipment Design”, “ Operation of […]

The hand tool set consists of three plastic cases, each of which contains a specific group of tools. The first case contains a general-functional set of tools: 1/4″»DR: Heads: 4, 4.5, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 13, 14 mm; Long heads: 6, 7, 8, 9, 10, 11, 12, 13 mm; Heads […]

Description. The simulator bench must simulate the operating mode and measure the output characteristics of the removed electrical equipment of trucks and tractors in order to check its functionality, as well as determine the technical condition and troubleshoot. Must ensure verification of: relay regulators; relay-breakers; electric drives of vehicle components; generators under load and at […]

The laboratory stand should be designed to carry out a set of practical work on studying the distribution system and light intensity in the headlights of modern cars with various light sources, as well as developing initial skills in diagnosing, maintaining and repairing a car as part of the course “Design, repair and operation of […]

Designed to measure compression (end of compression pressure) in the cylinders of diesel and carburetor engines at starting speeds of the engine crankshaft, which is one of the main indicators of the technical condition of the cylinder-piston group (CPG) and gas distribution mechanism (GRM). Deviation of compression from standard values ​​indicates a malfunction in one […]

A set of devices and tools for maintenance of batteries is designed to develop skills in servicing starter batteries when conducting practical classes in specialized disciplines in educational institutions. Description. A set of devices and tools for maintenance of rechargeable batteries is designed to develop skills in servicing starter batteries with an electrical capacity in […]

Simulator bench for testing, checking and adjusting diesel injectors with measurement Allows you to check: — injection start pressure and fuel atomization quality, — tightness of the shut-off cone, — hydraulic tightness along the shut-off cone and the guide cylindrical part. The time of pressure drop is recorded using a stopwatch. On the top of […]

The “Digital Tachograph” training stand is designed to teach students of car repair specialties from secondary and primary vocational education institutions the basics of working with devices of this type, methods of their installation, configuration, maintenance and operation in the conditions of car repair shops and bases of car repair enterprises. The training stand is […]

Purpose. The laboratory bench simulator is intended for carrying out a set of practical work on studying the technology of testing and washing gasoline injection nozzles, as well as developing initial skills in diagnosing, maintaining and repairing a car in the courses “Design of Automotive Equipment”, “Operation of Automotive Equipment”, “Design and calculation of automotive […]

Purpose. The training stand is designed for practical work on studying the technology for testing electrical equipment of passenger cars, the principles of their functioning and operating modes, as well as the formation of initial skills in diagnosing, maintaining and repairing a car in the courses “Design of automotive equipment”, “Operation of automotive equipment”, “Design […]

Purpose. The press is intended for technical and technological support of the educational process for carrying out repair work of various types of automotive equipment, as well as for the formation of initial skills in vehicle maintenance and repair in the courses “Design of Automotive Equipment”, “Operation of Automotive Equipment”, “Design and Calculation of Automotive […]

Purpose. The training stand is designed to carry out a set of practical works to study the design of passenger cars, the principles of their functioning and operating modes, as well as the formation of initial skills in diagnosing, maintaining and repairing vehicle gearboxes in the courses “Design of Automotive Equipment”, “Operation of Automotive Equipment” […]

Purpose. The tool trolley is designed to perform educational and practical work in general metalwork and auto repair in specialized courses at specialized educational institutions.

The device is intended for measuring diagonal dimensions, measuring the length and height of all types of cars when teaching the technology of the work process for restoring damaged car bodies weighing at least 3300 kg, as well as developing initial skills in diagnosing, maintaining and repairing car bodies in the courses “Design of Automotive […]

The slipway is intended for studying the technology of the work process for restoring damaged car bodies weighing at least 3300 kg, as well as developing initial skills in diagnosing, maintaining and repairing car bodies in the courses “Design of automotive equipment”, “Operation of automotive equipment”, “Design and calculation” automotive and tractor equipment» in institutions […]

The electronic measuring system must consist of a pointer target and a measuring beam with video cameras. The system must display the three-dimensional coordinates of the measured point, its displacement relative to the control one. The accuracy of the measuring system is no worse than 1.6 mm. The system must be capable of measuring the […]

Purpose. The training simulator is intended for carrying out training work on the technology of using rotation angle measuring transducers when teaching students of auto repair specialties in institutions of secondary and primary vocational education. Training in the basics of working with devices of this type, methods of their installation, configuration, maintenance and operation in […]